[admin]

Hello, please try the following.

1. Uninstall everything
Use Putty to check that the AdGuardHome folders under

Code:

/var/packages/..
/volume1/@appstore/..

are deleted.

2. Install the package without starting it afterwards.
3. Execute the command as in the instructions with root rights in Putty.

Code:

sed -i "s/package/root/g" /var/packages/AdGuardHome/conf/privileg

Go to the

Code:

/volume1/@appstore/AdGuardHome

directory and check whether the following folders are present.



4. Then run the following command:

Code:

/var/packages/AdGuardHome/target/AdGuardHome -s install

What is the output??

Code:

root@NAS:~# /var/packages/AdGuardHome/target/AdGuardHome -s install
2024/05/18 14:22:06 [info] AdGuard Home, version v0.107.44
2024/05/18 14:22:06 [info] service: control action: install
2024/05/18 14:22:08 [info] service: started
2024/05/18 14:22:08 [info] Almost ready!
AdGuard Home is successfully installed and will automatically start on boot.
There are a few more things that must be configured before you can use it.
Click on the link below and follow the Installation Wizard steps to finish setup                                      .
AdGuard Home is now available at the following addresses:
2024/05/18 14:22:08 [info] go to http://127.0.0.1:3000
2024/05/18 14:22:08 [info] go to http://[::1]:3000
2024/05/18 14:22:08 [info] go to http://192.168.1.236:3000
2024/05/18 14:22:08 [info] go to http://192.168.1.237:3000
2024/05/18 14:22:08 [info] go to http://172.17.0.1:3000
2024/05/18 14:22:08 [info] go to http://[fe80::42:aeff:fe87:526d%docker0]:3000
2024/05/18 14:22:08 [info] go to http://[fe80::7c89:4bff:fe45:3803%docker320846b                                      ]:3000
2024/05/18 14:22:08 [info] go to http://[fe80::a872:c5ff:fe5b:9572%dockerc2c0122                                      ]:3000
2024/05/18 14:22:08 [info] go to http://[fe80::38e6:a5ff:fe8d:5a34%dockerdea2454                                      ]:3000
2024/05/18 14:22:08 [info] go to http://[fe80::f0d2:2ff:fe29:eedd%docker9f8e952]                                      :3000
2024/05/18 14:22:08 [info] go to http://[fe80::4cbe:39ff:fed3:7df3%dockerf6daf39                                      ]:3000
2024/05/18 14:22:08 [info] go to http://[fe80::bc4f:18ff:feeb:3dd6%dockerea1d13f                                      ]:3000
2024/05/18 14:22:08 [info] go to http://[fe80::7481:2bff:fead:c727%docker5f136aa                                      ]:3000
2024/05/18 14:22:08 [info] go to http://[fe80::a095:5aff:fe39:62ff%docker109a95b                                      ]:3000
2024/05/18 14:22:08 [info] go to http://[fe80::24c7:1fff:fe39:4de%docker453e57a]                                      :3000
2024/05/18 14:22:08 [info] go to http://[fe80::f8db:a2ff:fee8:477f%dockerbd342f8                                      ]:3000
2024/05/18 14:22:08 [info] go to http://[fe80::34ab:fcff:fe35:4fa8%docker11ba8f5                                      ]:3000
2024/05/18 14:22:08 [info] go to http://[fe80::40ed:8dff:fe42:a4e%docker3da0898]                                      :3000
2024/05/18 14:22:08 [info] go to http://[fe80::1816:b2ff:fe2f:2c19%dockerc493a89                                      ]:3000
2024/05/18 14:22:08 [info] service: action install has been done successfully on                                       linux-systemd

5. After this run the following command:

Code:

/var/packages/AdGuardHome/target/AdGuardHome -s start

What is the output?? 

Code:

root@NAS:~# /var/packages/AdGuardHome/target/AdGuardHome -s start
2024/05/18 14:23:46 [info] AdGuard Home, version v0.107.44
2024/05/18 14:23:46 [info] service: control action: start
2024/05/18 14:23:50 [info] service: action start has been done successfully on linux-systemd

Greetz - The admin


After doing these 2  commands it starts.on the 220+ Thank you.

But on the 213j i  get this 

Code:

~# /var/packages/AdGuardHome/target/AdGuardHome -s install
-ash: /var/packages/AdGuardHome/target/AdGuardHome: cannot execute binary file: Exec format error

Code:

~# /var/packages/AdGuardHome/target/AdGuardHome -s start
-ash: /var/packages/AdGuardHome/target/AdGuardHome: cannot execute binary file: Exec format error

Hello, it seems that the ADGuardHome binary is not compatible with the DS213j architecture. 
This means that unfortunately you cannot use the application on the system. 

For your other system, the DS 220+, you now have three options to access the system: 

• http://192.168.1.236:3000 
  
• http://192.168.1.237:3000 
  
• http://172.17.0.1:3000 
  

To stop ADGuardHome if it not work with the Software Center you need the following command in putty:

Code:

/var/packages/AdGuardHome/target/AdGuardHome -s stop

If the solution helped you, be so kind and post it on YouTube and here in the forum.

Greetz - The Admin